Understanding log categories
Matrix logs hundreds of interactions into one of four log categories: informational, warning, error, and fatal.
Parameter
Description
info
Informational messages. They can be queried for trends. No action is required.
Example: New network settings have been applied
warn
Warning messages. They indicate a potential issue. An error might occur if corrective action is not taken in a given time.
Example: Error reading general config file
error
Error messages. They indicate non-urgent failures. These indicate changes or events that did not match expected results, such as a file could not be opened or program was busy. Typically, these are critical messages and must be addressed by changing some input value before the desired result is achieved or by your device administrator or developer.
Example: Unable to open CLI config file. No such file or directory
fatal
Fatal message. These messages indicate an imminent issue that should be corrected immediately, such as during updating the firmware or resetting the system defaults. Contact your support staff.
Example: Unable to apply firmware update!
<STRING> is a variable and may be a: word or words (for example, user name, host name, filter) or a number (for example, port number, version number, group ID).
Informational
Informational or info messages provide details about normal operational changes or events.
 

Accepted client tunnel connection
activated layout (<STRING>)
Apply firmware update requested
Applying Firmware Update.
Attempting to import new license
Authenticating user at DN: <STRING>
Authentication system restarted using scheme (<STRING>)
Authentication via web interface failed
Beginning Factory Reset.
Beginning Firmware Update.
Changed auth scheme (<STRING>)
changed default group id (<STRING>)
Changed IPv4 network interface setting '<STRING>' to <STRING>
Changed IPv6 network interface setting '<STRING>' to <STRING>
changed remote authentication setting <STRING> = <STRING>
Changed remote logging settings.
Changed time and/or time source.
Changed time source to <STRING>
CLI shutting down, invalid run mode
Closed client tunnel connection
Configuration backup restored
Created default layout
created filter (<STRING>)
created group (<STRING>)
created group <STRING>
created rule (<STRING>)
created user (<STRING>)
created user <STRING>
Created web session <STRING> for user <STRING>
Current extended version: <STRING>.<STRING>.<STRING>.<STRING>
(<STRING>.<STRING>.<STRING>.<STRING>.<STRING>) <STRING>/<STRING>
deleted filter (<STRING>)
deleted group <STRING>
deleted layout (<STRING>)
deleted rule (<STRING>)
deleted user <STRING>
Dummy log entry <STRING>
Ending <STRING>
Expiring web session: <STRING>
Factory clean initiated
Factory reset initiated
Factory reset requested
failed to create group <STRING>
failed to import <STRING> groups
failed to import <STRING> users
failed to update group <STRING>
<STRING> fault cleared.
Firmware status server listening on port: <STRING>
Firmware update succeeded. Rebooting system!
Firmware upgrade process complete.
Flash partition <STRING> attempt #<STRING>
Flash partition <STRING> succeeded
FPGA tunnel listening on port <STRING>
imported <STRING> groups
imported <STRING> users
Imported group <STRING>:<STRING>
Imported user <STRING>:<STRING>
IPv4 - Address: <STRING>, Netmask: <STRING>, Gateway: <STRING>
IPv4 - DHCP: <STRING>
IPv4 - DNS Servers: <STRING>, <STRING>
IPv6 - Address: <STRING>/<STRING>, Gateway: <STRING>
IPv6 - DHCP: <STRING>
IPv6 - DNS Servers: <STRING>, <STRING>
IPv6 - OFF
Last system reset caused by AHB.
Last system reset caused by SRESET.
Layout export finished without error
Layout import finished without error
Layout import operation started from CLI
LDAP URL: <STRING>
Listening on <STRING>
Log initialized. Version: <STRING>
modified filter (<STRING>)
modified network interface hostname
modified rule (<STRING>)
Network configuration was reset to default values
New network configuration was saved.
New network settings have been applied
NIMS Auth key update successful
NIMS Update Thread shutting down
NIMS Update Thread started
No user interface sections in firmware upgrade,
switch firmware upgrade.
Pending extended version: <STRING>.<STRING>.<STRING>.<STRING>
(<STRING>.<STRING>.<STRING>.<STRING>.<STRING>)
Ping thread ending.
Ping thread using gateway address '<STRING>'
Port <STRING> changed type. Wiping statistics.
Rebooting device
Rebooting the system
Received file <STRING> exceeds maximum length of <STRING>, length = <STRING>
Received file <STRING>, length = <STRING>
Received flash file <STRING>, length = <STRING>
Rejecting login by user <STRING> because the account is disabled
Rejecting login by user <STRING> because the user does
not belong to a group where login is enabled
Rejecting login by user <STRING> because the user does
not belong to any group
Reloading nilogd configuration file
Reloading time configuration file
Removing resources created by layout import
Request to <STRING> <STRING>
Reset to factory defaults succeeded. Rebooting system!
Resetting network configuration
restarting network interface
Restarting networking
saved layout (<STRING>)
Scp process finished
Scp process started
Select canceled, most likely due to interrupt
Select failed, most likely due to signal interrupt
Setting <STRING> power loss run state to <STRING>
Setting <STRING> power to OFF
Setting <STRING> power to ON
Shared Memory Size: <STRING>
Shutting down ping thread
Shutting down Socket Server
Shutting down SPI thread
Shutting down time sync thread
Shutting down watch thread
sizeof(HWCountsEntry): <STRING>
Skipping group <STRING>:<STRING> because a group
with that ID already exists
Skipping group <STRING>:<STRING> because a group
with that name already exists
Skipping user <STRING>:<STRING> because a user
with that ID already exists
Skipping user <STRING>:<STRING> because a user
with that username already exists
SPI thread shutting down
Starting <STRING>
Starting export of layout '<STRING>' to file '<STRING>'
Starting factory reset!
Starting import of layout file '<STRING>'
Starting NIMS update thread
State changed from <STRING> to <STRING>
Stopping NIMS update thread
System reboot requested
Time changed, clearing all statistics memory.
Unhandled HWApi event: 0x<STRING>
updated group (<STRING>)
updated group <STRING>
updated remote log and SNMP settings
updated user (<STRING>)
updated user <STRING>
User <STRING> was authenticated
User activated layout: <STRING>
User changed authentication configuration
User firmware update accepted
User generated a license request
User is uploading a backup
User is uploading new firmware
User logged in via web interface
User logged out via web interface
User saved layout: <STRING>
User uploaded NIMS key
Using <STRING> authentication
Watch thread shutting down
 
Warning
Warning or warn messages provide details about changes or events that are normal, but did not match expected results. Typically, these can be addressed by changing some input value and trying again.
 

Connections removed from unlicensed ports in layout '<STRING>'.
Could not find format for <STRING> Filter version: <STRING>
Could not get active layout id
Could not open filter file '<STRING>' for writing: <STRING>:<STRING>
Couldn't remove entry in file <STRING> because an entry with id
<STRING> doesn't exist
Couldn't replace entry in file <STRING> because an entry with id
<STRING> doesn't exist
Creating new layout ID for layout (<STRING>), layout ID not found on system
Did not receive OK command after file transfer
Error compiling <STRING> layout: <STRING>
Error getting file info - <STRING>:<STRING>
Error opening file '<STRING>' for reading: <STRING>:<STRING>
Error reading general config file
Error receiving handshake response: <STRING>-<STRING>
Error receiving handshake response: length was [<STRING>], expected [<STRING>]
Error sending apply layout response.
Error sending handshake request: <STRING>-<STRING>
Error sending notification of type <STRING>: <STRING>-<STRING>
Error setting ldap option: <STRING> - <STRING>
Excessive SPI bus errors: <STRING> CRC / <STRING> RX / <STRING> Loop
Filter file does not exist '<STRING>', cannot delete
Group description larger than <STRING> bytes
Invalid argument to RestoreBackupFileBytes
Invalid firmware finalize request - no firmware update active
Invalid layout name '<STRING>', cannot delete
Invalid RADIUS challenge length <STRING>
<STRING> layout did not pass validation
Layout '<STRING>' does not exist, cannot delete
Log file <STRING> was not loaded
LongPollThread unable to open counts object!
NIMS Unable to open socket to primary server: <STRING>:<STRING>
NIMS Unable to open socket to secondary server: <STRING>:<STRING>
No NIMS key available
Overwriting groups of new user <STRING> with default group: <STRING>
Ping: not an echo reply
Ping: received wrong id <STRING>
Ping: received wrong sequence # <STRING>
Response authenticator is invalid
Rule file does not exist '<STRING>', cannot delete
select error: <STRING> - <STRING>
Speed reduced on ports P%02d, P%02d, P%02d, P%02d in layout '<STRING>'
due to license restrictions.
TACACS+ Unable to connect to primary server: <STRING>:<STRING>
Truncating RADIUS attribute of <STRING> bytes
Trying to load active or pending <STRING> layout directly
Unable to acquire semaphores to update counts
Unable to allocate <STRING> bytes for request body
Unable to aquire lock to update counts
Unable to calculate RADIUS ResponseAuthenticator
Unable to configure blocking on socket: <STRING> - <STRING>
Unable to connect to NIMS at <STRING>:<STRING>
Unable to connect to NIMS at <STRING>:<STRING> - request timed out
Unable to create group <STRING> because it already exists!
Unable to create user <STRING> because name is not allowed!
Unable to create user <STRING> because they already exist!
Unable to create worker thread #<STRING>
Unable to find authentication scheme: <STRING>
Unable to find group: <STRING>
Unable to find groups from BaseDN=<STRING>, Filter=<STRING>:
<STRING> - <STRING>
Unable to find user: <STRING>
Unable to find users from BaseDN=<STRING>, Filter=<STRING>:
<STRING> - <STRING>
Unable to free lock after updating counts
Unable to generate a unique ID for filter: <STRING>
Unable to generate a unique ID for rule: <STRING>
Unable to get capabilities
Unable to get socket address: <STRING> - <STRING>. Using default values.
Unable to hash user password
Unable to iterate users from BaseDN=<STRING>, Filter=<STRING>:
<STRING> - <STRING>
Unable to locate command in CLI command description file (<STRING>):
<STRING> - <STRING>
Unable to lock HWApi mutex
Unable to lock mutex!
Unable to open CLI command description file (<STRING>):
<STRING> - <STRING>
Unable to open RADIUS connection to: <STRING>:<STRING>
Unable to read filter at: <STRING>
Unable to read from file <STRING>: <STRING> - <STRING>
Unable to read layout at: <STRING>
Unable to read property: <STRING>
Unable to read rule at: <STRING>
Unable to realloc <STRING> bytes for file: <STRING>
Unable to remove old layout <STRING> after renaming to <STRING>
Unable to remove rule references from layout: <STRING>
Unable to retrieve user DN
Unable to retrieve user entry
Unable to send auth packet to NIMS at <STRING>:<STRING>:
<STRING> - <STRING>
Unable to send notification (<STRING>) to hwcommd:
<STRING> - <STRING>
Unable to set read lock on file: <STRING> - <STRING>:<STRING>
Unable to set write lock on file: <STRING> - <STRING>:<STRING>
Unable to shutdown LongPollThread
Unable to start watch thread
Unable to stat file: <STRING> - <STRING>:<STRING>
Unable to stop NIMS update thread!
Unable to synchronize time to <STRING>: <STRING> - <STRING>
Unable to terminate firmware update
Unable to unlock mutex!
Unable to update remote user's groups: <STRING>
Unexpected FCGI Message Type: <STRING>
Unexpected message type from client: <STRING>
Unexpected NIMS Type: <STRING>
Unexpected version from client: <STRING>
Unhandled notification type: <STRING>
Unknown timestamp type specified: <STRING>
User <STRING> cannot be authorized because no default group is set.
User <STRING> failed authentication
User description larger than <STRING> bytes
UserDN <STRING> larger than maximum expected length: <STRING>
Warn: STDIN Padding - <STRING>
Warning, no work queue slots available for request
Warning, received message type <STRING> when expecting <STRING>
Warning, unable to allocate memory for client connection
Warning: Deleting rule (<STRING>) that is in use by active layout!
Warning: padding on FCGI_STDIN message!
Worker thread could not find work
 
Error
Error messages indicate changes or events that did not match expected results, such as a file could not be opened or program was busy. Typically, these are critical messages and must be addressed by changing some input value before the desired operation or result is achieved.
 

<STRING> fault detected!
Base64 encoded hash is an invalid length: <STRING>
Boundary length too large: <STRING>
Call to inotify_init failed - <STRING>:<STRING>
Can not set time before Jan 1, 2000
Canceling firmware update
Cannot apply firmware because no valid firmware is available.
Cannot begin firmware update because an update is already in progress.
Cannot begin firmware update due to insufficient memory.
Cannot begin firmware upload because an upload is already in progress.
Cannot cancel firmware upload because an upload is not in progress.
Cannot delete the group: <STRING>
Cannot delete the user: <STRING>
Cannot disable or change to remote login for group <STRING>!
Cannot disable or change to remote login for user <STRING>!
Cannot get permissions for user: <STRING>
Cannot lower permissions for group: <STRING>
Cannot lower permissions for user: <STRING>
Cannot parse multipart body - content type is not multipart: <STRING>
Cannot parse multipart body - no boundary specified for content type
Cannot parse multipart body - no content type provided
CLI error initializing cli system
Command failure during layout import (<STRING>), command: <STRING>
Critical sub-component firmware version mismatch!
DIGI_COMMAND_UNION_SIZE should be increased by <STRING>
DIGI_REGISTERS_UNION_SIZE should be increased by <STRING>
Duplicate wildcard entries for URI!
Entry <STRING> has invalid message size: <STRING>
Error accepting TLS connection from client
Error allocating data for multipart parser
Error allocating memory command nodes
Error allocating memory for PCLIStruct
Error allocating receive buffer of size <STRING>, file: <STRING>
Error binding to LDAP at <STRING>: <STRING> - <STRING>
Error compiling default <STRING> layout - <STRING>
Error connecting to hwcommd: <STRING>-<STRING>
Error copying license file: <STRING> - <STRING>
Error creating encrypted password buffer: <STRING>
Error creating group filter: '<STRING>' with '<STRING>'
Error creating license request, buffer too small
Error creating license request: <STRING>
Error creating LongPollThread
Error creating mutex
Error creating new user: <STRING>
Error creating temporary file - <STRING>:<STRING>
Error creating user filter: '<STRING>' with '<STRING>'
Error decompressing NIMS response
Error decrypting bind password
Error decrypting NIMS response
Error deleting filter file '<STRING>' (errno=<STRING>, <STRING>)
Error deleting filter: <STRING> - Unable to begin transaction
Error deleting layout file '<STRING>'
Error deleting layout: <STRING> - Unable to begin transaction
Error deleting rule file '<STRING>' (errno=<STRING>, <STRING>)
Error deleting rule: <STRING> - Unable to begin transaction
Error ending layout transaction: <STRING>-<STRING>
Error executing command <STRING>: <STRING> - <STRING>
Error expected filter file identifier of (0x<STRING>) but got
(0x<STRING>) instead
Error in NIMS response. Expected bulk header id of 0x<STRING>
Error initializing <STRING> authentication
Error initializing BPFParser!
Error initializing gzip
Error initializing hardware api
Error initializing HwApi
Error initializing LDAP: <STRING> - <STRING>
Error initializing LicenseSec library!
Error initializing mutex
Error initializing TLS connection with client
Error initializing TLS context
Error initializing TLS for firmware status
Error loading command definitions
Error mapping memory
Error moving pending layout to active layout: <STRING> - <STRING>
Error opening file <STRING> for writing: <STRING> - <STRING>
Error opening file <STRING>: <STRING> (<STRING>)
Error opening mem file: <STRING>
Error parsing scp command: <STRING>, command='<STRING>'
Error populating user dn: '<STRING>' with '<STRING>'
Error reading entry <STRING>: <STRING> - <STRING>
Error reading file <STRING> contents: <STRING>:<STRING>
Error reading from HttpRequest
Error reading from stdin - read() error, errno = <STRING>:<STRING>
Error reading from stdin - select() error, errno = <STRING>:<STRING>
Error reading header (<STRING> bytes)
Error reading pending layout
Error receiving firmware update!
Error receiving response: <STRING> - <STRING>
Error releasing queued item semaphore! <STRING> - <STRING>
Error reloading auth api configuration!
Error replacing filter references '<STRING>' -> '<STRING>' in saved
filters and rules
Error replacing filter references with filter value for
filter '<STRING>'
Error saving auth config file
Error saving compiled <STRING> layout
Error saving default <STRING> layout!
Error saving filter: <STRING>
Error saving filter: <STRING> - Unable to begin transaction
Error saving rule: <STRING> - Unable to begin transaction
Error send file command for file <STRING>
Error send file command for file <STRING>: <STRING> (<STRING>)
Error sending <STRING> bytes: <STRING> - <STRING>
Error starting socket server
Error starting TLS: <STRING> - <STRING>
Error transmitting SPI data. fd=<STRING>: <STRING> - <STRING>
Error truncating file to <STRING> bytes: <STRING> - <STRING>
Error upload is no longer active!
Error with flash firmware file, aborting flash operation
Error writing <STRING> bytes - <STRING>:<STRING>
Error writing entry <STRING> (<STRING> bytes):
<STRING> - <STRING>
Error writing entry <STRING>: <STRING> - <STRING>
Error writing file <STRING> contents: <STRING>:<STRING>
Error writing header (<STRING> bytes)
Error writing NIMS key to <STRING>
Error writing to file <STRING>
Error writing to file <STRING>: <STRING> (<STRING>)
Error writing to file: <STRING> - <STRING>
Error writing to partition <STRING> - <STRING>:<STRING>
Error, HTTP Response neither handled nor delegated
Error, invalid version from server: <STRING>
Error, unexpected filter file version found: <STRING>,
type: <STRING>
Failed to import group <STRING>:<STRING>
Failed to import user <STRING>:<STRING>
FATAL ERROR! Unable to start firmware upgrade
Fatal error, unable to open SPI slave pin!
Fatal error, unable to read WS_PPS: <STRING> - <STRING>
Fatal error, unable to read WS_SLAVE: <STRING> - <STRING>
FILTER_BUFFER_SIZE should be changed by <STRING>
Firmware update is not valid, aborting.
Firmware update status socket accept error
Firmware upgrade in progress, interface not available.
FIRMWARE_BUFFER_SIZE should be changed by <STRING>
fwrite() error
Group filter
Group name larger than <STRING> bytes
Handling unknown response!
Hardware returns error activating layout
Invalid backup file
Invalid config file
Invalid data size!
Invalid event type: <STRING>
Invalid file header!
Invalid firmware finalize request - did not receive all file sections
Invalid firmware finalize request - not all sections are valid
Invalid flash file: length = 0
Invalid shared memory pointer
Invalid state for Finalize EAPMD5
Keep Connection specified for worker thread request
Kernel image size is larger than kernel partition. Image Size:
<STRING> bytes, Partition Size: <STRING> bytes,
Last system reset caused by CPU Watchdog!
Layout export is not allowed when <STRING> is powered off
Layout file exceeds maximum size of <STRING> bytes
Layout file missing signature string: '<STRING>'
Layout import is not allowed when <STRING> is powered off
Layout import syntax error with line (<STRING>): '<STRING>'
LDAP API is not initialized
License does not specify # of licensed ports
License does not specify a valid Serial #
License does not specify max # of 10Gbps Blocks
License Serial # does not match our Serial #
License specifies an invalid # of 10Gbps Blocks
License specifies an invalid # of ports
Max number of clients (<STRING>) reached!
MCU returned error transferring firmware update!
nicli: expected format: -auth <username> <password>
nicli: expected format: -cmdhelp
nicli: expected format: -cmdusage
nicli: expected format: -exportlayout <layoutname> <exportfilename>
nicli: expected format: -help
nicli: expected format: -importlayout <importfilename>
nicli: unknown parameter: <STRING>
NIMS unable to open socket to any server.
No accessor for property: <STRING>
No Group ID attribute <STRING> for filter <STRING>
No Group Name attribute <STRING> for filter <STRING>
No ping reply within one second.
No read buffer
No User ID attribute <STRING> for filter <STRING>
No User Name attribute <STRING> for filter <STRING>
Not initialized or connected, state error.
Only <STRING> can set the password for <STRING>
Ping: malloc error
Ping: packet too short (<STRING> bytes) from <STRING>
Ping: recvfrom error
Ping: select()
Ping: sendto error
Ping: unable to open ICMP socket!
Port <STRING> is over-subscribed and has dropped packets
read() error
Received flash file <STRING>, length = <STRING>
RootFS image size is larger than rootfs partition. Image Size:
<STRING> bytes, Partition Size: <STRING> bytes,
select() error
Session manager not initialized
SHA1 Hash failed for section (<STRING>)
sizeof(digiRegisters_st): <STRING>
SPI_BUFFER_SIZE is not 4096!
Switch board firmware upgrade failed!
TACACS+ Error decrypting shared secret
TACACS+ Error reading from socket: <STRING> - <STRING>
TACACS+ Error sending request: <STRING> - <STRING>
TACACS+ Incomplete response received (<STRING> bytes)
TACACS+ Incomplete response received (<STRING>/<STRING> bytes)
TACACS+ Invalid SessionId
TACACS+ Unable to connect to any remote host
TACACS+ Unable to connect to secondary server: <STRING>:<STRING>
TACACS+ Unexpected packet type: <STRING>
TACACS+ Unexpected sequence. Expected: <STRING>, Got: <STRING>
TACACS+ Unknown Authentication Method: <STRING>,
pClient->pCfg->szAuthType
TACACS+ Unknown state!
TACACS+ Unknown status: <STRING>
The filter name \"<STRING>\" is already in use
The layout name \"<STRING>\" is already in use
The rule name \"<STRING>\" is already in use
There was an error resetting the network defaults via script:
<STRING>
There was an error updating network settings via script, restart
recommended: <STRING>
Too many wildcard URI parameters
Unable to add watch to <STRING> - <STRING>:<STRING>
Unable to allocate <STRING> bytes for file <STRING>
Unable to allocate <STRING> bytes for firmware update
Unable to allocate key for <STRING>:<STRING>
Unable to allocate memory
Unable to allocate UriTreeNode
Unable to apply firmware update!
Unable to attach memory for <STRING>:<STRING>
Unable to begin firmware update
Unable to bind firmware update socket: <STRING>-<STRING>
Unable to cancel firmware update transfer
Unable to change watchdog timeout. System will reset!
Unable to copy data, size exceeds buffer
Unable to create a session for user: <STRING>
Unable to create default layout
Unable to create firmware update socket: <STRING>-<STRING>
Unable to create license request, cannot property
Unable to create license request, cannot set property
Unable to create memory for <STRING>:<STRING>
Unable to create mutex
Unable to create RADIUS authentication type: <STRING>
Unable to create semaphore
Unable to create semaphore for <STRING>:<STRING>
Unable to create temporary file (<STRING>) for layout export:
<STRING> (<STRING>)
Unable to create temporary file (<STRING>) for layout import:
<STRING> (<STRING>)
Unable to decrypt AES key for file!
Unable to decrypt TACACS+ shared secret
Unable to erase memory block <STRING>(<STRING>-<STRING>) –
<STRING>:<STRING>
Unable to erase partition <STRING> - <STRING>:<STRING>
Unable to find queue match for RequestId: <STRING>
Unable to generate unique ID for layout '<STRING>'
Unable to get board serial
Unable to get clock time - aborting LongPollThread
Unable to get network addresses: <STRING> - <STRING>
Unable to get partition info <STRING> - <STRING>:<STRING>
Unable to get the current capabilities
Unable to get the current capabilities to activate layout
Unable to get the current capabilities.
Unable to import the license.
Unable to initialize gzip
Unable to initialize recv semaphore
Unable to listen firmware update socket: <STRING>-<STRING>
Unable to load active layout.
Unable to load filter list
Unable to load layout '<STRING>': <STRING>:<STRING>
Unable to load layout list
Unable to load rule list
Unable to load the active <STRING> layout
Unable to lock mutex
Unable to lock mutex - aborting LongPollThread
Unable to lock session manager lock
Unable to open <STRING>
Unable to open <STRING> for writing: <STRING> - <STRING>
Unable to open <STRING>: (<STRING>)
Unable to open CLI config file <STRING>: <STRING> - <STRING>
Unable to open EULA.txt: <STRING> - <STRING>
Unable to open file '<STRING>' - <STRING>:<STRING>
Unable to open file <STRING> for writing: <STRING> (<STRING>)
Unable to open file <STRING>: <STRING> - <STRING>
Unable to open log file <STRING>: <STRING> - <STRING>", pszPath
Unable to open memory for <STRING>:<STRING>
Unable to open ntpd.conf file for writing <STRING>:
<STRING> - <STRING>
Unable to open partition <STRING> for validation:
<STRING>:<STRING>
Unable to open ptpd.conf file for writing <STRING>:
<STRING> - <STRING>
Unable to open semaphore for <STRING>:<STRING>
Unable to open watchdog!
Unable to open WS_PPS: <STRING> - <STRING>
Unable to open WS_RDY: <STRING> - <STRING>
Unable to open WS_SLAVE: <STRING> - <STRING>
Unable to ping gateway!
Unable to populate user data
Unable to publish capabilities
Unable to queue firmware data in time allowed.
Unable to queue version info command.
Unable to read auth configuration file!
Unable to read entry <STRING>: <STRING> - <STRING>
Unable to read EULA version from file: <STRING>! <STRING>:<STRING>
Unable to read EULA version from file: '<STRING>'! <STRING>:<STRING>
Unable to read exported layout file <STRING>: <STRING> (<STRING>)
Unable to read file <STRING>: <STRING> (<STRING>)
Unable to read logging config file <STRING>: <STRING> - <STRING>
Unable to read logging configuration
Unable to read netmask: <STRING> - <STRING>
Unable to read network address: <STRING> - <STRING>
Unable to read nitime.cfg
Unable to read properties from license: <STRING>
Unable to read time config file <STRING>: <STRING> - <STRING>
Unable to reallocate memory
Unable to release semaphore
Unable to reload log configuration
Unable to reload logging configuration, restart may be necessary:
<STRING> - <STRING>
Unable to reload time configuration
Unable to rename layout <STRING> to <STRING> - Unable to save layout
Unable to rename layout: <STRING> - Layout <STRING> already exists
Unable to rename layout: <STRING> to <STRING> - Unable to load layout
Unable to request capabilities.
Unable to reset network config
Unable to resize file <STRING> to <STRING> bytes
Unable to restart networking
Unable to return semaphores after updating counts
Unable to save compiled <STRING> layout
Unable to save device id to file - <STRING>:<STRING>
Unable to save device id: <STRING>
Unable to save general configuration
Unable to save log configuration
Unable to save network configuration
Unable to save time configuration
Unable to seek in file: <STRING> - <STRING>
Unable to seek in file: <STRING> - <STRING>:<STRING>
Unable to send Factory Clean request
Unable to send queued SPI packet!
Unable to set hostname to: <STRING>
Unable to set power options
Unable to set semaphore value for <STRING>:<STRING> to <STRING>
Unable to set the options.
Unable to set the time.
Unable to set WS_PPS as INPUT: <STRING> - <STRING>
Unable to set WS_PPS as IRQ: <STRING> - <STRING>
Unable to set WS_RDY as OUTPUT: <STRING> - <STRING>
Unable to set WS_RDY to <STRING>: <STRING> - <STRING>
Unable to set WS_SLAVE as INPUT: <STRING> - <STRING>
Unable to set WS_SLAVE as IRQ: <STRING> - <STRING>
Unable to setup watchdog!
Unable to start firmware status thread
Unable to start firmware update
Unable to start NIMS update thread!
Unable to start SPI thread
Unable to start thread
Unable to stat file <STRING>: <STRING> (<STRING>)
Unable to truncate file: <STRING> - <STRING>
Unable to unlock memory block <STRING>(<STRING>-<STRING>) –
<STRING>:<STRING>
Unable to write alerts header: <STRING> - <STRING>
Unable to write entry: <STRING> - <STRING>
Unable to write layout to temporary file (<STRING>) for layout import:
<STRING> (<STRING>)
Unable to write ntpd.conf
Unable to write partition <STRING> - <STRING>:<STRING>
Unable to write ptpd.conf
Unable to write to file '<STRING>' - <STRING>:<STRING>
Unexpected NIMS Command: <STRING>
Unexpected NIMS Mode: <STRING>
Unknown FCGI Message Type: <STRING>
Unknown firmware file!
User password larger than <STRING> bytes
User: '<STRING>' does not have any permissions defined
Username larger than <STRING> bytes
Validate: error reading partition <STRING> - <STRING>:<STRING>
Validate: SHA1 Checksum failed for partition <STRING>
 
Fatal
Fatal messages indicate a serious problem that must be addressed before continuing.
 

Error initializing operation list
Error initializing Session Manager
Error initializing URI Tree
Invalid type type: <STRING>, expected: <STRING>
No read filter function defined for filter file
version: <STRING>, type: <STRING>
No read filter info function defined for filter file version:
<STRING>, type: <STRING>
Unable to allocate AuthScheme instance
Unable to apply firmware update!
Unable to initialize operation: <STRING>
Unable to read NI Public Key file!
Unable to reset to factory defaults!